Try Update NS0-184 Dumps For NetApp Certified Storage Installation Engineer, ONTAP

test2022-08-29T08:20:57+00:00

By test latest NS0-184 questions and answers, NetApp Certified Storage Installation Engineer, NS0-184 practice exam, ONTAP, Update NS0-184 Dumps 0 Comments

The latest NS0-184 Dumps are new updated for your best preparation to pass NetApp Certified Storage Installation Engineer, ONTAP exam. FreeTestShare team update our NetApp NS0-184 Dumps regularly, and the following is a sample of the most recent NS0-184 Exam Questions added to our NS0-184 Exam preparation solutions. To get a comprehensive set of updated test preparation resources, get NS0-184 Dumps with real exam questions and answers. With NS0-184 dumps, you can be confident that you will pass the NetApp NS0-184 exam on your first attempt.

Try NS0-184 practice questions below! You will face them on the actual exam!

Page 1 of 10

1. What are two ways to identify an AFF All SAN Array system? (Choose two.)

Use the san config show CLI command.

View the ONTAP System Manager system nodes.

Use the cluster image show CLI command.

View the ONTAP System Manager cluster settings.

2. What is NetApp’s best practice regarding Ethernet flow control?

Leave flow control enabled.

Disable flow control on the switch ports.

Disable flow control on the host, switch, and all node ports.

Disable flow control on all 10Gbps ports.

Disable flow control on cluster network ports in the Data ONTAP cluster.

3. What are two supported cluster interconnect switches for the FAS8040 nodes? (Choose two.)

Cisco Catalyst 2960

Cisco NX5596

NetApp CN1610

NetApp CN1601

4. You completed the installation of an AFF A700s with NetApp CN1610 switches. You used ports e0a and e0f with breakout cables to connect the controllers to the interconnect switches. After completing the cluster setup, ports e0e and e0i are not visible in OnCommand System Manager.

In this scenario, what caused this problem?

Breakout cables were used and the second port on the same ASIC became disabled.

This is a hardware error and you must open a case with NetApp Support.

You must first enable the ports using the network port modify command.

You are missing a license to enable those ports.

5. What is the maximum node count in a cluster when using NetApp CN1610 switches?

6. You installed a new FAS9000 with SAS disk shelves. You want to use write cache in this environment.

In this scenario, what should you do to accomplish this task?

You need to buy an SSD and set it up as a storage pool for write cache that is used for the aggregate that you need.

You need to buy an SSD and set it up as a Flash Pool for write cache that is used at the node that had an SS

You need to set up the caching policy as your requirement by using the Flash Cache NVMe module.

You need to buy an SSD and set it up as a Flash Pool for write cache that is used at the aggregate that had an SS

7. You installed a new 2-node FAS500f ONTAP 9.8 switchless cluster that serves NAS volumes to both NFSv4.1 and SMB clients. The host operating systems have full flow control enabled on their data ports.

In this scenario, which two flow control settings would you verify? (Choose two.)

Verify that the data network ports have full flow control disabled.

Verify that the cluster network ports have full flow control enabled.

Verify that the data network ports have full flow control enabled.

Verify that the cluster network ports have full flow control disabled.

8. You finished the installation of a 2-node cluster and want to determine whether HA is configured correctly.

What are two ways to accomplish this task? (Choose two.)

Use the OnCommand Performance Manager GU

Use the cluster ha show and storage failover show commands on the CL

Use the system node autosupport check show command on the CL

Use the OnCommand System Manager GU

9. You have completed the installation and verification of the cluster for a customer.

What is required to complete the event?

Present the customer with the posters included in the boxes.

Call your manager to let them know that you are finished.

Have the customer call NetApp Support to let them know that the installation is complete.

Have the contact sign a document saying that the installation is complete.

10. You complete a hardware installation on a CN1610 switch and establish a serial connection to the RJ45 port.

In this scenario, the established serial connection allows the installer to complete which two tasks for the switches initial configuration? (Choose two.)

to manually configure the static network information

to configure the switch with another CN1610 switch using Cross-Stack EtherChannel configuration for load balancing and performanc

to view network information that has been dynamically assigned to the management interface by the DHCP server on the network

to use the serial port connection as a diagnostic channel to the second CN1610 switch in the cluster interconnec

Page 2 of 10

11. Which statement is true about cluster interconnect?

It provides the core data network communication.

It is needed for the replication network between clusters

It transports the data between nodes if a Data LIF has a non-optimized path.

It is a management network for cluster administration and can be used for interconnect LIFs.

12. You just finished an AFF A300 installation with two DS224C disk shelves.

What are two ways to cable these disk shelves? (Choose two.)

Use alternative control path.

Use single-path H

Use quad-path H

Use multipath H

13. You want to add additional nodes to a cluster.

Which action will complete this task?

Run the node join command on the new nodes.

Run the cluster setup command on the new nodes.

Run the cluster join command on the existing cluster.

Run the cluster setup command on the existing cluster.

14. A customer is using a Cisco Nexus 5020 as a cluster network switch.

What would be used as a management network switch in this scenario?

Cisco Nexus 5020 1GbE ports

Cisco Nexus 5020 Expansion Module

Cisco Catalyst 2960

Cisco Catalyst 5000

15. You are preparing for the installation of a new AFF A400 system with NS224 NS224 storage shelves. You want to gather information on the connectivity options for the external shelves.

In this scenario, which NetApp tool would you use for this task?

Hardware Universe

Active IQ Config Advisor

Active IQ Unified Manager

Interoperability Matrix Tool

16. You are creating an aggregate on a new FAS8200 with two DS224C shelves. Your customer wants to be able to use the Disk Maintenance Center.

In this scenario, what is the minimum number of spare disks required per node and disk type?

17. What is the next step if you must escalate an open case?

Upload the support case and core data files to NetApp Suport and to Engineering.

Clustered Data ONTAP triggers the AutoSupport mechanism automatically again.

Call NetApp Support and ask to speak to the duty manager.

Call NetApp Support and open a new case.

18. A customer ordered two new DS224C shelves. The Customer wants you to add these shelves to an existing stack which consists of two DS2246 shelves.

Which statement is true in this scenario?

You need to order additional cables to expand the existing stack.

Mixing DS224C and DS2246 shelves in the same node is not supported.

You cannot mix DS224C and DS2246 shelves in the same stack.

DS224C shelves are supported with only new HBAs.

19. Click the Exhibit button.

You are installing a new AFF All SAN Array A700 HA pair.

Referring to the exhibit, which IP address would have been used to join node 02 to the cluster during setup?

192.168.0.112

169.254.212.198

169.254.145.151

192.168.0.101

20. A new AFF8200 has a four-port UTA2 adapter installed in slot 2. Using the ucadmin command, you see that these ports are configured for FC.

Which port names are correct in this scenario?

e0a/0a, e0b/0b, e0c/0c, e0d/od

e2a/2a, e2b/2b, e2c/2c, e2d/2d

e2a, e2b, e2c, e2d

2a, 2b, 2c, 2d

Page 3 of 10

21. How many spare disks are required to activate the maintenance center?

22. While installing new Cisco cluster switches, you need to download the appropriate RCF to the switch.

In this scenario, which two file transfer protocols would be used? (Choose two.)

HTTP

FTP

SCP

NFS

23. What is the purpose of a mailbox disk?

for shipping defective drives back to NetApp

for storing HA partner information

for logging

for sending AutoSupport mail

24. At a new Installation, you run Config Advisor and see the warnings shown In the exhibit.

What should you do to correct the warnings on the node?

Set the flow control on all the 10GbE ports to none, and delete the AutoSupport settings.

Set the flow control on all of the l0GbE or 40GbE cluster interconnect ports to None.

Delete all of the AutoSupport settings, and change the flow control to full.

Set the flow control on all the lGbE ports to match the 10GbE pods.

25. An iSCSI LIF fails to migrate during a storage failover test. In this scenario, why did the LIF not migrate?

A failover port was not defined

LIFs that serve block protocols do not failover

The failover policy was not configured

LIF failover was not enabled

26. You install a new 2-node FAS8200 switchless cluster. You want to reach all necessary management LIFs and SPs for this cluster.

How many management IP addresses do you need in this scenario?

27. An ONTAP cluster is installed at a secure site. The array has no access to the Internet but is managed 24/7 by onsite engineers. The customer requires that when hardware failures occur, the failures are reported to the NetApp Support team as quickly as possible.

In this scenario, which two tasks should be performed during the project hand-off procedure to satisfy the customer’s requirement? (Choose two.)

Ensure that Active IQ Config Advisor is installed.

Ensure that the onsite engineers receive EMS alerts when hardware issues occur.

Educate the onsite engineers about invoking the AutoSupport tool from ONTAP System Manager.

Educate the onsite engineer about how to manually log support calls.

28. In an ONTAP switched cluster, which three types of traffic travels over the cluster network? (Choose three.)

intercluster SnapMirror

intracluster SnapMirror

Epsilon voting

cluster database replication

remote cluster peering

29. You have completed a clustered Data ONTAP installation for a new customer. You are now ready to hand off the system to the customer.

Which three actions should you take at this stage in the installation process? (Choose three.)

Show the customer how to open a case with NetApp Support.

Demonstrate System Manager and its functionality.

Tell the customer to call their sales representative if there are further questions.

Tell the customer you are finished and then leave the site.

Show the customer how to set up a support account.

30. Where is user data (file access) written to by default?

Aggr0_root

Vol0_root

mailbox disks

SVM volume

Page 4 of 10

31. Select the exhibit tab.

The exhibit illustrates the network cabling of a 4 node HA duster that includes four separate networks.

Which two definitions are correct in this scenario? (Choose two.)

Each node must be connected to five distinct networks.

A cluster can be created without data network connections, but It must Include a cluster interconnect connection.

Each node may be connected to the management and cluster networks only.

A cluster cannot be created without data network connections, but it must Include a cluster interconnect connection.

32. To ensure that your customer’s cluster is robust and operational, you need to be familiar with configuration best practices.

Which three practice rules should you always follow? (Choose three.)

Keep all nodes in the cluster on the same version of ONTA

Use LIFs with defined failover policies.

Remove failed disk drives once a year to maintain minimum interruption in your controller stability.

All power supply units should be plugged into the same power grid.

Do not use the root aggregate for storing data.

33. After setting up a new cluster, you run an AutoSupport message for a test.

Which two commands would you use to proof the functionality and settings of AutoSupport? (Choose two.)

system node autosupport show history

system node autosupport show

system node autosupport option show

system node autosupport history show

34. You are adding nodes to an existing cluster. In this scenario, which three statements are correct? (Choose three.)

If you are adding a second node to a single-node cluster, the second node must have been installed, but the cluster network can be configured later.

You must add a cluster switch for every two nodes.

If you are adding nodes to a multiple-node cluster, more than half of the existing nodes in the cluster must be healthy.

The switchless cluster functionality is supported only in a single or two-node cluster.

If you are adding nodes to a two-node switchless cluster, you must have installed and configured the cluster management and interconnect switches before adding additional nodes.

35. During handover, a customer asks you how to obtain support from NetApp after installation.

What are two responses in this scenario? (Choose two.)

Visit.

Visit mysupport.netapp.com

Send an AutoSupport message from the system.

Contact Global Support by telephone.

36. You have finished the basic installation and validation of a clustered Data ONTAP system. The customer wants to create a test SVM using the CIFS protocol as a file server.

What basic information will be needed from the customer environment to complete this task? (Choose two.)

user ID and password with administrative privileges on the Active Directory

Windows Server and Active Directory version to check compatibility matrix

IP addresses, subnet mask, and default gateway to configure the SVM data LIF

customer switch model and version to verify with the compatibility matrix

37. After you deploy a 4-node AFF A220, you want to upgrade the ONTAP version of the cluster.

In this scenario, before the upgrade, which advanced CLI command is used to locate epsilon?

clustering ring show

cluster ha show

cluster show

cluster image show

38. Regarding clustered Data ONTAP 9, what happens to the roles of the on board ports, HBAs, and NICs?

These roles are assignet when LIFs are created.

These roles are assigned based on the controller type.

These roles are predefined and must be changed before creating your LIFs.

The roles are divided into two categories: Data Management and Node Management.

39. An ONTAP cluster implementation typically consists of which two network architecture elements? (Choose two.)

node interconnect

intercluster network

data network

cluster interconnect

40. After the Installation of a new NetApp FAS system, you use theNetAppDocs tool for site design documentation.

In this scenario, in which three document formats would you create an inventory report? (Choose three.)

.docx

.html

.pdf

.ps

.xlsx

Page 5 of 10

41. Upon finishing the Installation of a new system for a customer, they request that you train them on how to administer the system. In this scenario, which two responses are appropriate? (Choose two.)

Visit the NetApp MySupport Site and look for the Express Guides, they will guide you through the daily tasks and provide input and output examples.

If you have a specific issue, you can visit the Knowledge Base Web site (https://kb.netapp,com).

The answers to any of your questions can be found on the NetApp SmartSolve site (http://smartsolve.netapp.com).

You should open a case with NetApp Support for all future questions with low priority and include the keyword "Training" in the title.

42. Your customer plans to expand a 2-node FAS2750 switched cluster with two new controllers.

In this scenario, which two prerequisites should you examine in advance? (Choose two.)

Verify that the hard drives of the new controllers are compatible with the old controllers.

Verify that the existing cluster has a minimum 10 GB of free space for root volumes.

Verify that the existing switches support the additional controllers.

Verify that the platform of the new controllers can be mixed with the cluster’s existing controllers.

43. Exhibit:

You have an 8-node cluster, and sometimes the data LIFs fail over to a non-working port.

Referring to the exhibit, what must you do to solve this problem?

Configure more than one IPspace.

Configure the MTU consistently across the cluster

Configure the correct Ethernet ports in all broadcast domains.

Configure the LIFs using separate home nodes.

44. A remote administrator is connecting to a cluster from a different remote network.

According to NetApp best practices, which type of LIF routing is required to accomplish this task?

cluster LIF

data LIF

cluster management LIF

intercluster LIF

45. A customer has a six-node cluster running NFS and FCP. The customer wants to add nodes to the cluster.

How many nodes would be added in this scenario?

46. A customer wants you to add a disk shelf that contains SSDs so they can implement Flash Pool.

Which three tools would you use to complete this task? (Choose three.)

Use the My AutoSupport tool to ensure that Flash pool is licensed.

Use Hardware Universe to ensure that you would not exceed the maximum drive count.

Use Hardware Universe to ensure that you would not exceed the maximum cache for the system.

Use the My AutoSupport tool to see if there is a Flash Cache card installed.

Use Config Builder to verify the shelves can be added.

47. You need to add new nodes to an existing 4-node cluster that is using Cisco Nexus 3132Q-V cluster interconnect switches. You install the latest RCF file on the system and receive a syntax error.

What is the cause of this error?

You must copy and paste all of the commands in the RCF file.

The switches were already configured and had executed the commands twice causing this error.

You must clear the switch configuration before you apply a new RCF file.

RCF files are available for only NetApp switches.

48. In a 4-node cluster, what is function of the HA interconnect? (Choose the best answer.)

It provides the ability to relocate the aggregate ownership.

It provides the ability to synchronize the cluster configuration.

It provides nondisruptive operations and fault tolerance.

It provides the ability to migrate a data aggregate to any node in the cluster.

49. You create a new CIFS data LIF with the default failover group. In this scenario, where will the new LIF failover if the node that owns the new LIF panics?

to any port in the cluster that is operationally up

to any port in the cluster that is administratively up

to any available port in the same subnet

to any available port listed in the broadcast domain

50. Which three conditions would prevent a normal giveback operation? (Choose three.)

established NFS sessions

continuous SnapMirror relationships

LUNs mapped with ALUA

established CIFS sessions

presence of failed disks

Page 6 of 10

51. A customer must create VLAN 599 tagging on physical port e0g from cluster node filer1-01.

What is the name of the new VLAN interface?

e0g-vlan599

vlan599-e0g

vl599-e0g

e0g-599

52. Which two NetApp features encrypt storage data? (Choose two.)

NVE

NSE

TPM

NVMe

53. A customer is settings up a new cluster. The customer notices that there are many management ports on the cluster. The customer is know the purpose of the node management network LIF.

What do you tell customer in this scenario?

The node management LIF provides multiple IP address for managing a particular node in the cluster at the hardware level and is used for system maintenance.

The node management LIF is associated with a storage virtual machine (SVM) and is used for communicating with client.

The node management LIF provides a dedicated IP address for the entire cluster and can fail over to any node management or data port in the cluster.

The node management LIF provides a dedicated a IP address to managing a particular node in the cluster and is used for system maintenance.

54. While testing storage failover, you receive an error message indicating that you have a disk inventory mismatch.

What is a reason for the error message?

unsupported disks

cabling problems

Flash Cache problems

unowned disks

55. What is the function of the USB boot device?

It stores the primary kernel, secondary kernel, and core dumps.

It stores only the primary kernel.

It stores only firmware.

It stores the boot image, system firmware updates, and diagnostics.

56. You installed a new FAS8200 cluster and are configuring important EMS event notifications to be sent to the customer.

Which address must be set up for e-mail notifications in this scenario?

LDAP address

site address

partner address

mailserver address

57. Which two statements are true about the LIFs that are used for a cluster peer relationship? (Choose two.)

The MTU size must be set to 9000 bytes on all the LIFs used for the cluster peering.

The LIFs must use the default intercluster service policy.

The LIFs must be in dedicated broadcast domains an IPspaces.

At least one LIF per node is required on each cluster.

58. Exhibit:

Your ONTAP cluster shows the cluster network errors that are shown in the event log.

What is used by ONTAP software to log the errors that are shown in the exhibit?

BGP

AutoSupport

EMS

SNMP

59. While installing a new AFF A400 HA pair, you are unable to add an NTP server from another subnet. You are able to ping the NTP server from the new cluster.

In this scenario, what are two causes of this problem? (Choose two.)

The admin SVM has the wrong gateway.

A firewall is blocking port 123.

The time skew is too great.

The cluster management LIF needs to be in a different IPspace.

60. You finished a new installation and executed Config Advisor successfully. You review the physical racking and cabling on one of the controllers, and notice an amber light that was not previously on.

Which two actions should you perform before you turn over the cluster for production? (Choose two.)

Remove cables connected to the controller until you find the one responsible for the controller issue.

Review AutoSupport messages which could explain the controller state.

Execute Config Advisor again to check for new errors.

Let the customer know the cluster is operating normally while the amber LED is on.

Page 7 of 10

61. You are asked to install a 6-node cluster of FAS8080 controllers. The installation has been completed and Config Advisor shows no warnings or errors. The customer can ping and access the controller.

Which statement is true in this scenario?

This installation has not been completed successfully until you have confirmed that SSH is enabled.

This installation has not been completed successfully until the customer and NetApp Support have received a minimum of three AutoSupport messages.

This installation has been completed successfully only if you have confirmed that the configuration is correct.

This installation has been completed successfully, because Config Advisor would identify the missing configuration.

62. You are performing an installation of a clustered Data ONTAP and you reach the AutoSupport configuration point. You configured AutoSupport with all of the customer's information.

But when you trigger AutoSupport, the customer says that they did not receive the message, and neither did NetApp.

Which two actions must be verified? (Choose two.)

You can ping the mailhost from the NetApp storage systems.

The customer has enabled port 25 from the storage controllers on their firewall.

The customer has enabled routing of email-based messages from the storage controllers on their email server.

You can ping the NetApp Support site from the storage systems.

63. You are setting up a LIF for the node management network.

What will be the default failover policy in this scenario?

broadcast-domain-wide

system-defined

local-only

sfo-partner-only

64. You need to install a cluster with a FAS2720 HA pair and a FAS8300 HA pair.

Which NetApp tool will verify which cluster interconnect switches support this configuration?

Active IQ Config Advisor

Interoperability Matrix Tool (IMT)

Hardware Universe (HWU)

mysupport.netapp.com site

65. In which scenario must ACP be out-of-band?

when using DS4243 shelves with SATA drives and I0M6 modules

when using DS4243 shelves with SATA drives and IOM3 modules

when using DS4243 shelves with SSD devices and IOM12 modules

when using DS212C shelves with SSD devices and IOM12 modules

66. You are given a standard license key for NFS. In which scenario would this standard licensed be used?

The licensed is locked to a node with a specific serial number

The license will be available for any node in the cluster.

The license will be available for use on an HA pair for use.

The license is locked to a cluster with a specific serial number.

67. What are two ONTAP storage efficiency technologies that would be used on an AFF A400 cluster? (Choose two.)

Flash Pool

FlexClone volumes

FlashCache

thin provisioning

68. You are ready to purchase a new FAS8200 six node cluster. In this scenario, which three switches are supported as NetApp cluster interconnect switches.

Cisco nexus 5596UP

Cisco Nexus 5548UP

Cisco Nexus 3132Q-V

Cisco CN1610

Brocode 7840

69. You are preparing for the installation of a new 2-node switchless AFF A250 ONTAP 9.8 cluster and need to obtain the preinstallation information from the customer.

In this scenario, what are three examples of data required from the customer? (Choose three.)

management IP addresses

cluster switch name

gateway IP address

BMC IP addresses

cluster name

70. Click the Exhibit button.

During an ONTAP cluster handover procedure, your customer asks how to identify and solve issues that might occur on the newly deployed array.

Referring to the exhibit, which two widgets would the customer use to help with these issues? (Choose two.)

Guide Me

Active IQ

Contracts and Warranties

ASE Corner

Page 8 of 10

71. When you install a new ONTAP 4-node cluster, which network type is required?

data network

peering network

cluster interconnect

intercluster network

72. After installing cluster switches, you want to verify that the switches are operating as they should.

What would allow you to accomplish this task?

Use Config Builder.

Use the cluster ping-cluster command in privilege advanced mode.

Use the network device-discovery command in privilege advanced mode.

Use OnCommand System Manager.

73. Which three components are required when setting up a new ONTAP cluster? (Choose three.)

password

cluster management IP

node management IP

Advanced Drive Partitioning

intercluster IP

74. You have to disable a switch that is connected to a port on your FAS2750. You notice that the LIFs that are associated with this port are migrated to a port that is not expected.

In this scenario, what would cause this behavior?

The network port is configured incorrectly.

The broadcast domain is configured incorrectly.

There are no online ports within the same failover group.

The network failover port is not licensed.

75. You are planning to update your running switch environment. You need to determine if certain conditions exist before the FASTPATH software and reference configuration file (RCF) on a NetApp CN16xx cluster switch can be installed.

Which condition must exist in this scenario?

You must set the port configuration to default for all ports before running the portcfgdefault portnumber command.

The cluster must be a fully functioning cluster (no error log messages or other issues).

All ISL ports must be moved to a different switch.

You can only update your switch environment within offline windows.

76. Click the Exhibit button.

A customer wants to replace their ONTAP cluster CN1610 switches with Cisco Nexus 3132Q-V switches. They want to perform a non-disruptive upgrade.

Referring to the exhibit, which cable will be required to non-disruptively migrate to the new switches?

a 10GbE SFP+ to SFP+ cable

a 100GbE QSFP28+ to 4x25GbE SFP28+ cable

a 40GbE QSFP+ to QSFP+ cable

a 40GbE QSFP+ to 4x10GbE SFP+ cable

77. What is the maximum number of data disks that a RAID-TEC RAID group has?

78. You want to enable secure communication with the SP or BMC through CA-signed certificates.

Which two certificate types must be installed in this scenario? (Choose two.)

cluster certificate

server certificate

root CA certificate

ONTAP certificate

79. A customer wants to expand a 10-node AFF A700s NAS cluster running with Cisco Nexus 3132Q-V cluster interconnect switches using new nodes.

In this scenario, what is the maximum number of nodes to be added into this cluster?

80. You are setting up a new cluster. The customer notices that there are many management ports on the cluster. The customer wants to know the purpose of the cluster management LIF.

In this situation, what should you tell the customer?

The cluster management LIF provides a dedicated IP address for the entire cluster and can fall over to any port in the cluster that Is available in the broadcast domain.

The cluster management LIF provides a dedicated IP address for managing a particular node in the cluster and is used for system maintenance.

The cluster management LIF is used to carry Intracluster traffic between nodes In a cluster and must be created on a 10GbE network port.

The cluster management LIF provides multiple IP addresses for the entire cluster and can fall over to any cluster or intercluster ports.

Page 9 of 10

81. You are deploying a new AFF All SAN Array A250 into a customer’s existing data fabric.

In this scenario, which two tools would give insight into their existing Cisco MDS fabric configuration? (Choose two.)

Brocade SAN Health

Cisco Data Center Network Manager (DCNM)

Active IQ

Active IQ Config Advisor

82. You have installed a new 2-node FAS9000 cluster with two external shelves. You want to make sure that each node has two paths to each disk in the shelves.

How do you verify your configuration?

Use the storage show disk -p command.

Use the storage disk option show command.

Use the disk show -fields initiator command.

Use the sysconfig command.

83. Given:

Which three classes successfully override printOne()? (Choose three.)

Option A

Option B

Option C

Option D

Option E

Option F

84. You want to create a data volume on aggr0 and you receive a message with the following warning: ''Warning: You are about to create a volume on a root aggregate.

This may cause severe performance or stability problems and therefore is not recommended. Do you want to proceed?''

What is the reason for this severe performance or stability problem?

Controller failover and storage failover are separate processes that must occur in parallel, otherwise problems will arise.

The performance load generated by the data volume can be very strong, so it should not be shared with vol0 on aggr0, requiring a separate aggregate for it.

The performance load generated by the vol0 cannot be shared with any other volume on aggr0, requiring a dedicated aggregate for it.

Controller failover and storage failover are separate processes that must occur at different times, otherwise problems will arise.

85. You are installing a 4-node cluster with two CN1610 switches. Your co-worker is setting up the switches, but accidentally deletes the current configuration.

According to NetApp, what is the recommended way to restore the configuration?

Install only one switch.

Manually configure the ports as they are designated in the CN1601 and CN1610 Switch Setup and Configuration Guide.

Reload the same reference file to the switch.

Copy the configuration from a switch that is working.

86. Which command would be used to measure the throughput and latency of traffic between nodes?

qos statistics workload performance show

cluster ping-cluster

network test-path

statistics node show

87. You are asked to add a new HA pair to an existing 2-node switchless AFF A220 cluster. You must first convert to a 2-node switched cluster using Broadcom BES-53248 cluster switches.

Which two conditions must be fulfilled before you start the migration? (Choose two.)

All cluster LIFs must be in the up state and on their home ports.

The “Enabled Switchless Cluster” option must be manually set to “false”.

All cluster LIFs must have an MTU size of 1500.

The 2-node switchless configuration must be properly set up and functioning.

88. You completed an ONTAP cluster deployment as a reseller engineer. During the knowledge transfer process to the customer, they ask for proof that the array has correct multi-path HA cabling deployed and that the array is error free.

Which documentation output would you present to the customer to satisfy this requirement?

Active IQ Unified Manager output

NetAppDocs output

Config Advisor output

Active IQ OneCollect output

89. Set the adapter to status-admin up.

90. You are asked to Install an AFF A700 with two DS224C shelves fully populated. When you arrive, the customer asks you to install an additional shelf.

Which shelf would you add to this cluster?

a DS224C shelf fully populated with SAS drives

a DS224C shelf fully populated with SATA drives

a DS2246 shelf fully populated with SSD drives

a DS4486 shelf fully populated with SATA drives

Page 10 of 10

91. Select the Exhibit tab.

Referring to the exhibit, a customer wants to migrate LIF lif1 iscsi to node cluster1-02 port e0d, but they receive an error.

What is the cause of this error?

The LIF is not properly configured.

The destination port is not available.

This type of LIF cannot be migrated.

The LIF does not have a failover group.

92. Select the Exhibit tab.

You finished the installation of a new FAS8200 system. The customer wants to use FC and 10G Ethernet but only has the onboard UTA2 ports available.

Referring to the exhibit, which two sets of ports would the customer use? (Choose two.)

e0e, 0f and e0g, 0h

0e, 0f and e0g, e0h

0e, e0f and 0g, e0h

e0e, e0f and 0g, 0h

93. What is a protocol?

SnapRestore

CIFS

SnapMirror/SnapVault

FlexClone